Inhaltsverzeichnis

Hardware

Netzwerkgeräte

Switch

Name VLAN Phys. Ports
todesstern-1 FA 21, 22, 23, 24
todesstern-3 FA 4

VLAN-Router

Name Firmware Ziel FA-intern
TPLink OpenWRT V. 23.x 192.168.250.0/24 192.168.250.1

Accesspoints

Name Firmware Ziel Name Switch
TPLink OpenWRT V. 23.x 192.168.250.1 Farpoint todesstern-1
TPLink OpenWRT V. 23.x 192.168.250.2 Farnborough todesstern-2

IOT-Geräte

Schaltsteckdose: nous smart tasmota wifi socket A1T

nous-a1t-smarte-steckdose-tasmota-firmware-wlan-4er-set.pdf

Mac Bereich
08:3A:8D:F0:A8:31 Elektronik
08:3A:8D:F0:8B:3F Elektronik
08:3A:8D:F0:B5:06 Elektronik
08:3A:8D:F0:B3:3B Elektronik
08:3A:8D:F0:98:1D Elektronik
08:3A:8D:F0:9D:FB Elektronik
C8:C9:A3:1E:08:4E Elektronik
08:3A:8D:F0:9A:4C Elektronik
34:94:54:83:7D:6F
7C:87:CE:B8:07:BC
34:94:54:83:6D:80
34:94:54:83:88:B2
34:94:54:83:3C:DC
34:94:54:83:00:9C
34:94:54:83:5E:C2
34:94:54:83:86:3D
34:94:54:83:6E:45
34:94:54:83:5D:9F
34:94:54:83:61:FB
34:94:54:83:3C:3F
34:94:54:83:78:EC
34:94:54:83:75:AA
34:94:54:83:3C:DB
34:94:54:83:70:A9
34:94:54:83:56:98
34:94:54:83:66:02
34:94:54:83:70:F8
34:94:54:83:6E:15
34:94:54:83:5A:4A
34:94:54:83:38:FA
34:94:54:83:2F:0B
34:94:54:83:35:64
34:94:54:83:63:DD
34:94:54:83:85:85
34:94:54:83:83:C2
34:94:54:83:37:E8
34:94:54:83:60:4A
7C:87:CE:B7:0F:8C
34:94:54:83:5C:36
34:94:54:83:3B:FC
34:94:54:83:77:33
34:94:54:83:36:A3
34:94:54:83:79:33

Tasmota Konfig-RESET:

7x Ein / Aus (Einschaltzeit < 10 s) - beim 7. Mal eingeschaltet lassen

  1. Cut power from the device completely for 30 seconds
  2. Power the device on and off six times with intervals lower than 10 seconds and leave it on after seventh time
  3. Fast power cycle device recovery should activate and the device should be reset to firmware defaults

Einrichtung:

  1. plug the socket for energy
  2. connect to tasmota @ local AP (192.168.4.1)
  3. tasmota: configure wifi „Sternenlabor“you can use this link –> http://192.168.4.1/wi?s1=Sternenlabor&p1=%21Sternenlabor99%21&save=–> write down IP-address: 192.168.200.#
  4. tasmota: connect to tasmota @ Sternenlabor 192.168.200.#
  5. tasmota: configure MQTT
  6. EXT: check MQTT –> IP: 192.168.200.# (MQTT Explorer)
  7. tasmota: get MAC
  8. MAN: label the plug with the last six MAC-Numbers
  9. WIKI: insert MAC into the upper table
  10. EXT: configure wifi „slfa“ - Accesspoints –> Farpoint (192.168.250.1 bzw. 192.168.200.16) / Farnborough (192.168.250.2) to accept MAC from tasmota
  11. tasmota: configure wifi „slfa“
  12. EXT: check MQTT –> IP: 192.168.250.# (MQTT Explorer)

Konfiguration