projekte:fabaccess:hardware
Dies ist eine alte Version des Dokuments!
Inhaltsverzeichnis
Hardware
Netzwerkgeräte
Switch
| Name | VLAN | Phys. Ports |
| todesstern-1 | FA | 21, 22, 23, 24 |
| todesstern-3 | FA | 4 |
VLAN-Router
| Name | Firmware | Ziel | FA-intern |
| TPLink | OpenWRT V. 23.x | 192.168.250.0/24 | 192.168.250.1 |
Accesspoints
| Name | Firmware | Ziel | Name | Switch |
| TPLink | OpenWRT V. 23.x | 192.168.250.1 | Farpoint | todesstern-1 |
| TPLink | OpenWRT V. 23.x | 192.168.250.2 | Farnborough | todesstern-2 |
IOT-Geräte
Schaltsteckdose: nous smart tasmota wifi socket A1T
nous-a1t-smarte-steckdose-tasmota-firmware-wlan-4er-set.pdf
| Mac | Bereich |
| 08:3A:8D:F0:A8:31 | Elektronik |
| 08:3A:8D:F0:8B:3F | Elektronik |
| 08:3A:8D:F0:B5:06 | Elektronik |
| 08:3A:8D:F0:B3:3B | Elektronik |
| 08:3A:8D:F0:98:1D | Elektronik |
| 08:3A:8D:F0:9D:FB | Elektronik |
| C8:C9:A3:1E:08:4E | Elektronik |
| 08:3A:8D:F0:9A:4C | Elektronik |
| 34:94:54:83:7D:6F | |
| 7C:87:CE:B8:07:BC | |
| 34:94:54:83:6D:80 | |
| 34:94:54:83:88:B2 | |
| 34:94:54:83:3C:DC | |
| 34:94:54:83:00:9C | |
| 34:94:54:83:5E:C2 | |
| 34:94:54:83:86:3D | |
| 34:94:54:83:6E:45 | |
| 34:94:54:83:5D:9F | |
| 34:94:54:83:61:FB | |
| 34:94:54:83:3C:3F | |
| 34:94:54:83:78:EC | |
| 34:94:54:83:75:AA | |
| 34:94:54:83:3C:DB | |
| 34:94:54:83:70:A9 | |
| 34:94:54:83:56:98 | |
| 34:94:54:83:66:02 | |
| 34:94:54:83:70:F8 | |
| 34:94:54:83:6E:15 | |
| 34:94:54:83:5A:4A | |
| 34:94:54:83:38:FA | |
| 34:94:54:83:2F:0B | |
| 34:94:54:83:35:64 | |
| 34:94:54:83:63:DD | |
| 34:94:54:83:85:85 | |
| 34:94:54:83:83:C2 | |
Tasmota Konfig-RESET:
7x Ein / Aus (Einschaltzeit < 10 s) - beim 7. Mal eingeschaltet lassen
- Cut power from the device completely for 30 seconds
- Power the device on and off six times with intervals lower than 10 seconds and leave it on after seventh time
- Fast power cycle device recovery should activate and the device should be reset to firmware defaults
Einrichtung:
- connect to tasmota @ local AP (192.168.4.1)
- tasmota: configure wifi „Sternenlabor“
- tasmota: connect to tasmota @ Sternenlabor
- tasmota: configure MQTT
- EXT: check MQTT –> IP: 192.168.200.# (MQTT Explorer)
- tasmota: get MAC
- MAN: label the plug with the last six MAC-Numbers
- EXT: configure wifi „slfa“ - Accesspoints –> Farpoint (192.168.250.1 bzw. 192.168.200.16) / Farnborough (192.168.250.2) to accept MAC from tasmota
- tasmota: configure wifi „slfa“
- EXT: check MQTT –> IP: 192.168.250.# (MQTT Explorer)
projekte/fabaccess/hardware.1729011720.txt.gz · Zuletzt geändert: 2024/10/15 19:02 von peter.cranz