projekte:fabaccess:hardware
Dies ist eine alte Version des Dokuments!
Inhaltsverzeichnis
Hardware
Netzwerkgeräte
Switch
| Name | VLAN | Phys. Ports |
| todesstern-1 | FA | 21, 22, 23, 24 |
| todesstern-3 | FA | 4 |
VLAN-Router
| Name | Firmware | Ziel | FA-intern |
| TPLink | OpenWRT V. 23.x | 192.168.250.0/24 | 192.168.250.1 |
Accesspoints
| Name | Firmware | Ziel | Name | Switch |
| TPLink | OpenWRT V. 23.x | 192.168.250.1 | Farpoint | todesstern-1 |
| TPLink | OpenWRT V. 23.x | 192.168.250.2 | Farnborough | todesstern-2 |
IOT-Geräte
Schaltsteckdose: nous smart tasmota wifi socket A1T
nous-a1t-smarte-steckdose-tasmota-firmware-wlan-4er-set.pdf
| Mac | Bereich | |
| 08:3A:8D:F0:A8:31 | Elektronik | |
| 08:3A:8D:F0:8B:3F | Elektronik | |
| 08:3A:8D:F0:B5:06 | Elektronik | |
| 08:3A:8D:F0:B3:3B | Elektronik | |
| 08:3A:8D:F0:98:1D | Elektronik | |
| 08:3A:8D:F0:9D:FB | Elektronik | |
| C8:C9:A3:1E:08:4E | Elektronik | |
| 08:3A:8D:F0:9A:4C | Elektronik | |
| 34:94:54:83:7D:6F | ||
| 7C:87:CE:B8:07:BC | ||
| 34:94:54:83:6D:80 | ||
| 34:94:54:83:88:B2 | ||
| 34:94:54:83:3C:DC | ||
| 34:94:54:83:00:9C | ||
| 34:94:54:83:5E:C2 | ||
| 34:94:54:83:86:3D | ||
| 34:94:54:83:6E:45 | ||
| 34:94:54:83:5D:9F | ||
| 34:94:54:83:61:FB | ||
| 34:94:54:83:3C:3F | ||
| 34:94:54:83:78:EC | ||
| 34:94:54:83:75:AA | ||
| 34:94:54:83:3C:DB | ||
| 34:94:54:83:70:A9 | ||
| 34:94:54:83:56:98 | ||
| 34:94:54:83:66:02 | ||
| 34:94:54:83:70:F8 | ||
| 34:94:54:83:6E:15 | ||
| 34:94:54:83:5A:4A | ||
| 34:94:54:83:38:FA | ||
| 34:94:54:83:2F:0B | ||
| 34:94:54:83:35:64 | ||
| 34:94:54:83:63:DD | ||
| 34:94:54:83:85:85 | ||
| 34:94:54:83:83:C2 | ||
| 34:94:54:83:37:E8 | ||
| 34:94:54:83:60:4A | ||
| 7C:87:CE:B7:0F:8C | ||
| 34:94:54:83:5C:36 | ||
| 34:94:54:83:3B:FC | ||
| 34:94:54:83:77:33 | ||
| 34:94:54:83:36:A3 | ||
| 34:94:54:83:79:33 | ||
Tasmota Konfig-RESET:
7x Ein / Aus (Einschaltzeit < 10 s) - beim 7. Mal eingeschaltet lassen
- Cut power from the device completely for 30 seconds
- Power the device on and off six times with intervals lower than 10 seconds and leave it on after seventh time
- Fast power cycle device recovery should activate and the device should be reset to firmware defaults
Einrichtung:
- plug the socket for energy
- connect to tasmota @ local AP (192.168.4.1)
- tasmota: configure wifi „Sternenlabor“you can use this link –> http://192.168.4.1/wi?s1=Sternenlabor&p1=%21Sternenlabor99%21&save=–> write down IP-address: 192.168.200.#
- tasmota: connect to tasmota @ Sternenlabor 192.168.200.#
- tasmota: configure MQTT
- EXT: check MQTT –> IP: 192.168.200.# (MQTT Explorer)
- tasmota: get MAC
- MAN: label the plug with the last six MAC-Numbers
- WIKI: insert MAC into the upper table
- EXT: configure wifi „slfa“ - Accesspoints –> Farpoint (192.168.250.1 bzw. 192.168.200.16) / Farnborough (192.168.250.2) to accept MAC from tasmota
- tasmota: configure wifi „slfa“
- EXT: check MQTT –> IP: 192.168.250.# (MQTT Explorer)
projekte/fabaccess/hardware.1734019780.txt.gz · Zuletzt geändert: 2024/12/12 17:09 von peter.cranz